Creat loopback interface

Newbie452061 Posted 2024-Aug-28 01:47

Hello everyone

Can you help me please how to creat loopback interface on sangforngaf and link it with ip sec tunnel as peer

Enrico Vanzetto has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

Hi, to set up a loopback interface on Sangfor NGAF and link it with an IPsec tunnel, follow these steps:

Create a Loopback Interface:

Log in to the Sangfor NGAF management console.
Go to Network > Interfaces > Loopback Interfaces.
Click “Add” to create a new loopback interface.
Set the IP address and subnet mask.
Save your changes.

Configure the IPsec Tunnel:

Head over to Network > IPsec VPN > VPN Connections.
Click “Add” to start a new IPsec VPN connection.
Enter the connection details like name, local and remote IPs, and authentication methods.
Use the loopback interface’s IP address as the local IP.
Adjust the IKE and IPsec settings as needed.
Save the configuration.

Link the Loopback Interface with the IPsec Tunnel:

Make sure the loopback interface is selected as the local interface in the IPsec VPN settings.
Set up NAT rules to allow the loopback interface to handle outbound and inbound VPN connections.
Create security policies to permit traffic between the loopback interface and the IPsec tunnel.

Verify the Configuration:

Check the IPsec tunnel status under IPsec VPN > Status.
Ensure the tunnel is active and traffic is flowing correctly.
Is this answer helpful?
Enrico Vanzetto Lv4Posted 2024-Aug-28 14:38
  
Hi, to set up a loopback interface on Sangfor NGAF and link it with an IPsec tunnel, follow these steps:

Create a Loopback Interface:

Log in to the Sangfor NGAF management console.
Go to Network > Interfaces > Loopback Interfaces.
Click “Add” to create a new loopback interface.
Set the IP address and subnet mask.
Save your changes.

Configure the IPsec Tunnel:

Head over to Network > IPsec VPN > VPN Connections.
Click “Add” to start a new IPsec VPN connection.
Enter the connection details like name, local and remote IPs, and authentication methods.
Use the loopback interface’s IP address as the local IP.
Adjust the IKE and IPsec settings as needed.
Save the configuration.

Link the Loopback Interface with the IPsec Tunnel:

Make sure the loopback interface is selected as the local interface in the IPsec VPN settings.
Set up NAT rules to allow the loopback interface to handle outbound and inbound VPN connections.
Create security policies to permit traffic between the loopback interface and the IPsec tunnel.

Verify the Configuration:

Check the IPsec tunnel status under IPsec VPN > Status.
Ensure the tunnel is active and traffic is flowing correctly.
Newbie452061 Posted 2024-Aug-28 17:16
  
in the setting > interdfaces i dont have loopback interfaces
Newbie452061 Posted 2024-Aug-28 17:20
  
this screen from my ngaf

Screenshot 2024-08-28 121811.png (7.33 KB, Downloads: 4)

Screenshot 2024-08-28 121811.png
Enrico Vanzetto Lv4Posted 2024-Aug-28 20:22
  
Hi, on a Sangofr NSF on our customer, i see the sub menu about loopback interfaces.
Are you using Sangofr NGAF or Sangfor NSF?
Please tell me the version of your Sangfor Device


8250166cf1640be53b.png (44.53 KB, Downloads: 6)

8250166cf1640be53b.png
Zonger Lv5Posted 2024-Aug-28 21:57
  
To create a loopback interface on a Sangfor NGAF and link it with an IPsec tunnel as a peer, you can follow these steps:

On the Sangfor NGAF, go to "Network" > "Loopback Interface" and create a new loopback interface with a unique IP address. Then, go to "VPN" > "IPsec" and create a new IPsec tunnel. In the "Peer" section, select the loopback interface you created as the peer's IP address.

Additionally, configure the IPsec tunnel's authentication and encryption settings as needed. Finally, save the changes and verify that the IPsec tunnel is established successfully.
Imran Tahir Lv4Posted 2024-Sep-18 12:40
  
informatic information

I Can Help:

Change

Board Leaders