Sangfor NGAF IPsec VPN not create

Newbie676529 Lv1Posted 04 Mar 2024 20:10

Last edited by Newbie676529 04 Mar 2024 20:13.

Hi There,

I have two NGAFs in HA (active - passive).
License available - Expiration Date: Never, Branch VPN Sites: 10, Lines: 10. Version: 8.0.47
I can’t select an interface in Basic Settings > VPN Paths > +Add
The Add item is not active.
How can I activate it?

Thanks.

vpn01.jpg (85.08 KB, Downloads: 246)

vpn01.jpg

Newbie517762 has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

HiHi,

Please review the below regarding your SSLVPN License Activation.

Please find the attached file for the License Activation Method.
License Activation Method.pdf (167.76 KB, Downloads: 287)
Is this answer helpful?
CLELUQMAN Lv4Posted 05 Mar 2024 09:07
  
Hi.
Have u already enable the VPN service ?

Network>IPSecVPN>Status
Newbie517762 Lv5Posted 05 Mar 2024 09:20
  
HiHi,

Please review the below regarding your SSLVPN License Activation.

Please find the attached file for the License Activation Method.
License Activation Method.pdf (167.76 KB, Downloads: 287)
mdamores Posted 05 Mar 2024 11:39
  
Go to Basic Settings > VPN Paths > +Add and see if +Add is Active. If not, this could be due to several reasons. You may check some troubleshooting guides below:

1. Check if your user account has administrative privileges to configure VPN paths. You credentials should have permission to add new paths
2. Check if your current license covers the number of desired VPN paths. As you mentioned, 10 branch VPN sites 10 lines so make sure that your license can accommodation those numbers
3. Validate if the interface you intend to use for VPN path is properly configured and enabled on Sangfor NGAF device to be selectable for VPN path creation
4. The version is quite updated but check for possible bugs or limitations of your current version. You may refer to  Sangfor official documentation for additional reference.
Newbie676529 Lv1Posted 05 Mar 2024 13:43
  
Hi, friends.
I have administrator rights to create a VPN.
The licenses are activated and the service is enabled.
This is the first VPN.
NGAF overloaded.

vpn02.jpg (67.95 KB, Downloads: 233)

vpn02.jpg
CLELUQMAN Lv4Posted 05 Mar 2024 15:51
  
Have u tried to restart your NGAF?
jerome_itable Lv3Posted 05 Mar 2024 16:29
  
1. Verify Permissions:

    Ensure you have the necessary administrative privileges to create VPN paths. Contact your network administrator if you're unsure about your permissions level.

2. Check License Compatibility:

    Verify that your current license allows for adding new VPN paths. Your license information mentions 10 Branch VPN Sites and 10 Lines. Ensure adding another path wouldn't exceed these limitations.

3. Consider Software Version:

    Sangfor NGAF version 8.0.47 might be older and might have limitations compared to newer versions. Check the Sangfor documentation or support to see if there are known issues with the "Add" button functionality in your specific version.

4. Explore Alternative Options:

    If adding a new VPN path through the user interface is not possible, explore alternative methods depending on your specific scenario. The Sangfor documentation or support might offer guidance on:
        Command-line interface (CLI): Some configurations might be possible through CLI commands.
        Upgrading software: Upgrading to a newer version might resolve the issue if it's a known bug in your current version.

5. Contact Sangfor Support:

    If none of the above suggestions resolve the issue, it's recommended to contact Sangfor support directly. They can provide the most accurate and up-to-date information and assistance specific to your configuration and license situation.
Newbie517762 Lv5Posted 05 Mar 2024 16:43
  
HiHi

Please try rebooting the Sangfor NGAF device and check if the "+Add" button becomes available.
If the above steps do not resolve the issue, contact Sangfor support for further assistance.
Tech.Support@sangfor.com
Newbie676529 Lv1Posted 05 Mar 2024 16:49
  
Hi, friends.
Overloaded (restart ) physically .
I couldn't find any IPsec VPN settings in Cli.
There is only: Sangfor_NGAF_v8.0.47_User Manual_EN.pdf

vpn05.jpg (35.88 KB, Downloads: 223)

vpn05.jpg
Zonger Lv5Posted 05 Mar 2024 20:19
  
To activate the interface selection in Basic Settings > VPN Paths > +Add on your NGAF (High Availability) with the given license and version, follow these steps:

1. Ensure that both NGAF devices are running the same version (8.0.47) and have the latest firmware updates installed.
2. Check if the interfaces you want to use for VPN paths are in an up and operational state. If not, bring them up using the appropriate interface configuration commands.
3. Make sure that the interfaces you want to use for VPN paths are not in the same subnet as the management interface of the NGAF. This is a common restriction in the system configuration.
4. Verify that the interfaces you want to use for VPN paths are not already configured as the primary or secondary interfaces in the system settings.
5. If none of the above steps resolve the issue, try resetting the web GUI configuration of your NGAF devices. This can be done through the CLI using the command "reset config" or by accessing the web GUI and navigating to System > Backup & Restore > Reset Configuration.

I Can Help:

Change

Moderator on This Board

11
7
5

Started Topics

Followers

Follow

1
3
5

Started Topics

Followers

Follow

0
4
5

Started Topics

Followers

Follow

67
20
3

Started Topics

Followers

Follow

3
14
3

Started Topics

Followers

Follow

1
137
3

Started Topics

Followers

Follow

Board Leaders