How to find out whether BGP status is established or not in ngaf

masih_pemula Lv1Posted 26 Feb 2024 12:16

How to find out whether BGP status is established or not in ngaf

CLELUQMAN has solved this question and earned 10 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go


Network > Routes >  BGP
Is this answer helpful?
CLELUQMAN Lv4Posted 27 Feb 2024 11:53
  

Network > Routes >  BGP
Newbie517762 Lv5Posted 27 Feb 2024 12:02
  
Hi,

Pls refer the attachment file - 1.1.3 Test Process(P.14) for Ref.

Network Secure_8.0.85_Best Practice_BGP over GRE over IPsec.pdf (1.83 MB, Downloads: 262)
Enrico Vanzetto Lv4Posted 27 Feb 2024 17:09
  
Hi, you can see the estabilished status through Ngaf web ui on Network -> BGP -> Neighbors.
Farina Ahmed Lv5Posted 27 Feb 2024 18:20
  
To determine whether the BGP (Border Gateway Protocol) status is established in NGAF (Next-Generation Firewall), you can typically check the BGP neighborship status through the firewall's management interface or command-line interface. In most NGAF platforms, you would execute commands like "show bgp summary" or "show ip bgp summary" depending on the vendor's syntax. Look for the status of BGP peers; if it shows "Established," then the BGP session is up and functioning correctly, indicating successful communication and route exchange between BGP peers. If the status is anything else, such as "Idle" or "Active," further investigation is needed to troubleshoot and resolve the connectivity issue.
pmateus Lv2Posted 27 Feb 2024 19:25
  
Hi,

You can go to Network > Routes >  BGP.
Prosi Lv3Posted 27 Feb 2024 21:12
  
If the route was received from a peer, run the display bgp vpnv4 all peer command to check whether the BGP peer relationship is in the Established state.
rivsy Lv5Posted 28 Feb 2024 15:28
  
In the NGAF Platform dashboard click Network then select Routes on the right side and choose BGP. From there you can check the status of it.
Zonger Lv5Posted 28 Feb 2024 20:42
  
Please follow below steps to find out whether BGP status is established or not in NGAF

Access the NGAF Web UI --> Navigate to the BGP Status --> Check BGP Status --> View BGP Peer Details --> Verify BGP Configuration
jerome_itable Lv3Posted 29 Feb 2024 08:36
  
Here are two methods to determine the BGP status in Sangfor NGAF:

Method 1: Using the Web Management Console:

    Access the Sangfor NGAF web management console.
    Navigate to the Network section.
    Click on BGP.
    The displayed information will include the BGP status for each peering connection. This will indicate whether the connection is "Established" or not.

Method 2: Using the CLI:

    Access the Sangfor NGAF command-line interface (CLI).
    Enter the following command:

show bgp neighbors

    The output will display details about BGP neighbors, including their BGP state. Look for the state associated with your specific peering connection. If it shows "Established," the BGP session is up and running.

I Can Help:

Change

Moderator on This Board

11
7
5

Started Topics

Followers

Follow

1
3
5

Started Topics

Followers

Follow

0
4
5

Started Topics

Followers

Follow

67
20
3

Started Topics

Followers

Follow

3
14
3

Started Topics

Followers

Follow

1
137
3

Started Topics

Followers

Follow

Board Leaders