#Configuration# Configure SNMP on Sangfor NGAF so that it can be read in real time in the Prtg-Admin
  

Sangfor Jojo Lv5Posted 19 Jul 2024 15:11

  
*Product: NGAF
  
*Version: 8.0.47
  
*1. Introduction
1.1Scenario

In this article, we will introduce how to use the SNMP protocol to monitor the Sangfor NGAF device. The services that will be monitored are CPU resource usage, memory availability, and interface traffic (eth2). This is needed for a network engineer because it is very practical, effective & efficient. Whenever and wherever you can monitor the condition of the firewall in the company with your smartphone.

The test results obtained from the SNMP settings in Sangfor NGAF were then displayed with Prtg admin, the results of monitoring the NGAF device, namely the condition of CPU, memory, and traffic in a real-time conditions interface.

1.2 Requirements

1). The user has an NGAF Firewall device
2). Have 1 PC for the prtg-admin server
  
  
*2. Configuration Guide
  
2.1. Activate the snmp
  
An important step to be able to monitor services on Sangfor is to activate the SNMP protocol. Then add the snmp trap along with the prtg-admin server address.
  
You can see the steps below:
1) Click the menu System >SNMP
2) Click the tick to enable SNMP
3) Choose SNMPv1/2
4) Press Add

5) The window dialogue SNMPv1/2, fill with below:
Name: PRTG-admin
Type: IP address
IP address: 192.168.0.100 (example ip server prtg).
Community: local_network

6) Press the Save button to save the configuration. If successful, it will look like the image below:
  
           
  
From here Sangfor has finished configuring, and you can use the SangforSNMP on the monitor server prtg-admin.

  
2.2. The test
  
From the test results in the prtg-admin monitoring software, the following are obtained:
a. CPU usage of the sangfor NGAF
The CPU usage on the Sangfor NGAF device is seen at 14%.

b. Memory usage of the Sangfor NGAF
Memory usage on Sangfor NGAF devices appears to be 51%.

c. The traffic from interface eth2 Sangfor NGAF.
The data traffic passing through the eth2 interface looks as big as 209.87 kbit/s.

  
*3. Precaution
   
To avoid failures in reading data, ensure that the IP and community of the SNMP configuration are correct.


This article is written by @Medicwho is a technical engineer in the network security field. If you want to know more about him, click here.


If you want to share articles like troubleshooting cases or configuration guides and get paid 4000 coins, please click the link below to register for this event.

6_Configure SNMP on Sangfor NGAF so that it can be read in real time in the Prtg.pdf

431.29 KB, Downloads: 174

6_Configure SNMP on Sangfor NGAF so that it can be read in real time in the Prtg.pdf

430.99 KB, Downloads: 174

Like this topic? Like it or reward the author.

Creating a topic earns you 5 coins. A featured or excellent topic earns you more coins. What is Coin?

Enter your mobile phone number and company name for better service. Go

vesogi7900 Lv2Posted 19 Jul 2024 18:38
  
Thank You soo much
Enrico Vanzetto Lv4Posted 19 Jul 2024 19:57
  
HI, thanks for sharing. I send a similar guide to Sangfor to collect smnp information about NGAF device on Zabbix Server.
Prosi Lv3Posted 22 Jul 2024 10:14
  
Thank you for this information
Newbie517762 Lv5Posted 23 Jul 2024 15:21
  
Thank you for the useful information.
Sheikh_Shani Lv2Posted 24 Jul 2024 22:01
  
Thanks For Sharing
juni Posted 27 Jul 2024 00:59
  
thanks for sharing