NGAF Load link balancing

Julius Lv1Posted 08 Sep 2022 13:37

Hi, Does anyone already implement wan link load balancing, round robin? Can you please guide me for configuration. Thanks folks

Newbie517762 has solved this question and earned 20 coins.

Posting a reply earns you 2 coins. An accepted reply earns you 20 coins and another 10 coins for replying within 10 minutes. (Expired) What is Coin?

Enter your mobile phone number and company name for better service. Go

HiHi,

Please find the attched file for Configuration Guide & pls refer Chapter 6 - Link Load Balancing Route.

Configuration Step:
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located)
Step 3. Source IP (All)
Step 4. Destination IP group (All)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3
Step 7. Others can be kept as default Sample Configuration

I hope it can be help you, thanks.

SANGFOR_NGAF_v8.0.35_Policy-Based Routing Configuration.pdf (901.28 KB, Downloads: 737)
Is this answer helpful?
Newbie517762 Lv5Posted 08 Sep 2022 15:02
  
HiHi,

Please find the attched file for Configuration Guide & pls refer Chapter 6 - Link Load Balancing Route.

Configuration Step:
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located)
Step 3. Source IP (All)
Step 4. Destination IP group (All)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3
Step 7. Others can be kept as default Sample Configuration

I hope it can be help you, thanks.

SANGFOR_NGAF_v8.0.35_Policy-Based Routing Configuration.pdf (901.28 KB, Downloads: 737)
jetjetd Lv5Posted 09 Sep 2022 01:31
  
Link Load-Balancing Route Configuration

Multiple lines can backup each other so that multiple lines can be used at the sametime without wasting bandwidth. There are four type of policy for link-load balancing:
Requirements: All internal network users will go to the external network througheth1. The method being choosed here is prefer link at top.

Configuration:
1) Fill in the policy name (Any will do)
2) Source Zone (where the internal network user is located)
3) Source IP (All)
4) Destination IP group (All)
5) Select HTTP application in the Application
6) Interface (Select eth1 and eth2)
7) Others can be kept as default



Take Note:
After the policy has been configured, the policy will be added at the top by default.Since the policy here are matched from top to bottom, it is necessary to move thispolicy to the back to ensure that the previous policy does not become invalid. Asfollows:

Thank you very much.
rivsy Lv5Posted 13 Sep 2022 10:16
  
You may check this video
kmrnliaqat Lv3Posted 13 Sep 2022 14:22
  


Network --->>Route -->>Policy Based Route
Imran Tahir Lv4Posted 13 Sep 2022 14:44
  
Network then route then load banlancing

then select the Ethernet for load bnalancing
Noviyanto Lv3Posted 13 Sep 2022 15:44
  
Maybe there's a way to implement it in resources. You can find and download there
Ali Jawwad 12 Lv1Posted 13 Sep 2022 17:55
  

Configuration Step:
Step 1. Fill in the policy name (Any will do)
Step 2. Source Zone (where the internal network user is located/LAN)
Step 3. Source IP (All)
Step 4. Destination IP group (All/ANY/WAN)
Step 5. Select HTTP application in the Application
Step 6. Interface (Select eth1 and eth 3/WAN
Faisal P Posted 13 Sep 2022 22:28
  
The use of load balancing with multiple WAN links can provide simultaneous outbound traffic efficiency and optimizing bandwidth.


Pat Lv4Posted 14 Sep 2022 08:22
  


You may also check on this youtube link

I Can Help:

Change

Moderator on This Board

11
7
5

Started Topics

Followers

Follow

1
3
5

Started Topics

Followers

Follow

0
4
5

Started Topics

Followers

Follow

67
20
3

Started Topics

Followers

Follow

3
14
3

Started Topics

Followers

Follow

1
137
3

Started Topics

Followers

Follow

Board Leaders